Ocserv Authentication - RADIUS (radcli)

Author: Mauro Gaspari


This Recipe provides step by step instructions on how to install, configure, and test RADIUS Authentication for Openconnect Server. This recipe focuses on generic installation instructions, from packages available on Openconnect server and radcli websites. No precompiled binary packages will be used, therefore this recipe applies to all linux distributions.

Platforms used for testing

This Recipe was tested on the following platforms:



Since version 0.10.6 ocserv RADIUS authentication depends on either libradius-client 1.1.7 or radcli libraries. At the time of writing, many distributions only offer libradius-client 1.1.6. In order to avoid unmet dependencies or radius libraries lagging behind ocserv in any way, Nikos Mavrogiannopulos decided to create the radcli libraries. These are updated to match ocserv requirements, and are easy to install and use. This recipe includes instructions to compile radcli libraries.

NOTE: radcli (or libradius-client) need to be installed before ocserv. If ocserv is compiled before radius libraries, it will build without radius support. Even if radius libraries are compiled/installed afterwards, it will not work, and ocserv will return errors when you try to start the service with RADIUS authentication enabled.

Network settings used on this recipe


Install radcli through your distribution channels (minimum recommended version is 1.2.5) or see the manual installation instructions.

radcli configuration (No TLS)

  1. Move to radcli etc folder cd /etc/radcli/

  2. Open radiusclient.conf with text editor

    nano radiusclient.conf
  3. Configure radius settings according to your environment. Following lab details for this recipe, we will need to change the following parameters:

    nas-identifier fw01  
    servers /etc/radcli/servers  
    dictionary /etc/radcli/dictionary  
    radius_timeout 10  
    radius_retries 3  
    bindaddr *
  4. Save and exit (in nano, ctrl+o to save, then ctrl+x to exit)

  5. Open servers file with text editor

    nano servers
  6. Configure servers settings according to your environment. Following lab details for this recipe we will need to add one line to servers file: radiustestsecretpassword 
  7. Save and exit (in nano, ctrl+o to save, then ctrl+x to exit)

Security considerations and radcli configuration with TLS.

If you have security concerns, for example on a corporate network, there are several ways to secure radius communications. One very common way to achieve this, is by isolating vlans.
If your RADIUS server requires TLS authentication of radius messages for security reasons, or if you are unable to implement separate management vlans, please use radiusclient-tls.conf instead of radiusclient.conf, and servers-tls instead of servers. Radius configuration with TLS is out of the scope of this document. Having said that, comments on radiusclient-tls.conf and servers-tls are clear and a system admin should have no issue with configuration.

Ocserv Installation

You can install ocserv using distribution packages. If ocserv is not available in your package manager, you can follow instructions on Ocserv installation recipe, available here: Ocserv Installation - Generic

Ocserv Configuration for Radius authentication

In order to enable radius authentication for ocserv, follow the steps below.

  1. Move to ocserv folder.
cd /etc/ocserv
  1. Open ocserv.conf with text editor

    nano ocserv.conf
  2. Comment all lines starting with “auth =”, it should look like this:

    #auth = "pam"  
    #auth = "pam[gid-min=1000]"  
    #auth = "plain[passwd=./ocserv.passwd]"  
    #auth = "certificate"  
    #auth = "radius[config=/etc/radiusclient/radiusclient.conf,groupconfig=true]"  
  3. Add a line as follows:

    auth = "radius [config=/usr/local/etc/radcli/radiusclient.conf,groupconfig=true]"
  4. If you need RADIUS accounting, add a line in the “Accounting methods available” Section:

    acct = "radius [config=/usr/local/etc/radcli/radiusclient.conf,groupconfig=true]"

Final notes

This concludes Ocserv Authentication - RADIUS (radcli) recipe. At this point Openconnect server should be working with radcli RADIUS libraries.